Some of you might want to know how gel blaster guns are used correctly, since more and more people have taken up the hobby. This guide will answer the most common questions about gel blasters. This article is very helpful for anyone who wants to learn how to gel blast.

How Does Gel Blaster Work?

How to set up a Gel Ball Blaster

These are the steps to setting up a ball shooter.

1. Read all instructions. The most important part is to read the instructions. They will show you how to use your gel blaster.
2. The gel balls must be hydrated prior to use. The time it takes to hydrate gel balls will depend on the type you use. They need to soak in water for at least 4-6 hours or overnight.
3. You can load the gelballs into the magazine of your gel blaster. You will need to know the correct way to load your magazine. There are several types.
4. The air pump is powered by the battery in most gel blasters. The battery compartment of a gel blaster is typically located on the handle.
5. Switch on the gelblaster. You will usually find a switch located on the side.
6. Aim & Shoot After turning on the gel blaster, you can aim & shoot your target.

Here’s some more tips on how to set up a ball blaster.

• To hydrate your gel balls, use clean, clear water. It will make them swell uniformly and keep them from breaking.
• Don’t overfill the magazine. The gel balls can jam up in the magazine if you do this.
• Check that the battery is correctly inserted. Gel blasters will not function if the battery is not correctly inserted.
• When using a Gel Blaster, wear eye protection. It will protect your eyes against the gel balls.

How to Assemble Gel Blast?

These are the steps to build a water bead gun:

1. Get your materials and tools together. A screwdriver and pliers are required, as well as the gel blaster.
2. The parts of a gel blaster may vary depending on the type. Most gel blasters are made up of the following components:
   • A barrel
   • A magazine
   • A trigger
   • A grip
   • A stock
   • A battery
   • A spring
   • A piston
3. Assemble main body of gel blaster. You may need to screw the trigger, grip, barrel, and magazine together.
4. Insert a battery. Usually, the battery compartment is located on the handle.
5. Gel balls are loaded into the magazine of the gelblaster. You will need to know the correct way to load your magazine. There are several types.
6. Check the gelblaster. After the gelblaster has been assembled, it should be tested to ensure it is working properly.

Tips for assembling the gelsoft:

• Do not overtighten screws. The gel blaster can be damaged if you overtighten the screws.
• Check that the battery is correctly inserted. Gel blasters will not function if the battery is not correctly inserted.
• When assembling the gel blaster, wear eye protection. It will protect your eyes against any flying pieces.

How do you turn on the gel blaster guns?

The specific model may affect the process for turning on a Gel Blaster. Here are some general instructions on how to activate a gelblaster:

1. Find the power switch. Usually, the power switch can be found on the side of or top the gel blaster.
2. Switch the power switch on. It may be a switch, button or dial.
3. Make sure the safety on the gel blaster is deactivated. It is located usually near the trigger.
4. Pull the trigger to test if it is on. The gel blaster will fire if it is on.

Here’s some more information on how to turn on a Gel Blaster:

• Check that the battery is correctly inserted. Gel blasters will not function if the battery is not correctly inserted.
• Check the fuse if the gel blaster won’t turn on. The fuse is normally located in the battery compartment.
• Contact the manufacturer if the gel blaster does not work.

How do you charge your gel blasters?

How to Grow orbeez in order to use Splatter Ball Guns

How to grow Orbeez gel blaster.

1. Gather all your materials. A bowl, water and Orbeez are required.
2. Fill up the bowl with water. How much water you will need depends on how many Orbeez are in your growing.
3. Submerge the Orbeez in water. Ensure that the Orbeez is completely submerged.
4. Set the timer to 4-6 hours. This is how long it takes Orbeez hydrates.
5. The Orbeez will be fully hydrated after 4-6 hours. To check, squeeze one Orbeez. It is fully hydrated if it feels soft and squishy.
6. Drain water from the bowl. This can be done by using a colander or pouring out the water.
7. Your Orbeez can now be used in your Gel Blaster. Store them in an airtight bag until you’re ready to use.

Orbeez gel blaster growing tips:

• Use filtered water or bottled. Orbeez will not absorb any impurities in the water if you use filtered or bottled water.
• Use only cold water. Orbeez can be damaged by hot water.
• Warm water can be used to speed up the process of hydration if you’re in a rush. Do not use boiling or hot water.
• The Orbeez will shrink a little once they are fully hydrated. This is perfectly normal.
• Orbeez can last up to six months in an airtight storage container.

How do you load gel guns?

How to load the gel blaster

1. Prepare gel balls. Gels balls must be hydrated prior to use. The time it takes to hydrate gel balls will depend on the type you use. They need to soak in water for at least 4-6 hours or overnight.
2. Find the magazine. A magazine is a part of a gel blaster which holds gel balls. You will find different magazines for your gel blaster. Make sure you understand how to load it.
3. Open the Magazine. You will need to lift or press a latch or button to open it.
4. Load all the gel balls in the magazine. All the gel balls must be placed into the magazine as a single layer. Overfilling the magazine can cause gel balls to jam.
5. Close magazine. After the gel balls have been loaded, close magazine by pressing the button or latch.
6. Insert magazine into gel blaster. Magazine should be inserted until it clicks in place.
7. The Gel Blaster is now ready for use.

How to load a gel blaster

• To hydrate your gel balls, use clean, clear water. It will make them swell uniformly and keep them from breaking.
• Don’t overfill the magazine. The gel balls can jam up in the magazine if you do this.
• Make sure that the magazine is correctly inserted. Gel blasters will not function if the magazine is not correctly inserted.
• When loading a blaster, wear eye protection. It will protect your eyes against the gel balls.

We recommend loading your orbeez pistol with a speedloader such as this:

Why Should you use dry fire gel ball blasters?

You should not dry-fire a gelblaster. Dry firing is firing a firearm without ammunition. This is the same as firing a gun without gel balls.

Dry firing a Gel Blaster can damage the gun. The barrel can be damaged if the firing pin strikes it. The firing pin may also be damaged, preventing the gun from firing correctly.

Dry firing can also be dangerous. The firing pin could strike the barrel so hard that it breaks. The barrel can break and send flying pieces. This could cause injury to someone.

It is therefore important that you never dry fire your gel blaster. You can practice your aim with a laser or a dry-fire trainer.

Conclusion

The gel blaster gun is a safe and fun way to enjoy being outdoors. These guns are also great for improving your hand-eye co-ordination and practicing your aim.

This blog post will teach you how to use a gel ball blaster gun. How to set up the gel blaster toy, load it and fire it are all covered in this blog post. You will also find some safety tips for using your gelblaster.

This guide will hopefully be informative and useful to you. Please contact us if you have further questions.

These tips will help you to have a fun and safe experience with your gel blaster.